How do you refresh a green feathers camera?

How do you refresh a green feathers camera?

If the camera is powering on please reset the camera by holding down the white button for 30 seconds and then try setting it up again.

How do I reset my green feathers WiFi camera?

Resetting the camera and setting to AP mode Press and hold the reset button for 5 seconds; you will hear it say ‘Reset, camera reboot’. Wait for the camera to say ‘Wait for WiFi config’. Now press the reset button three times. Wait for it to play three notes again.

How do I reset my WIFI camera?

Connect your camera to your router using an ethernet cable. Ensure your camera is connected to power. Use a straightened paperclip to press and hold the recessed reset button for 10 seconds.

How do I fix my WiFi camera?

How to fix a wireless IP camera not working or connecting to the internet

1. Make sure the wireless IP camera has sufficient power.
2. Make sure the password is correct.
3. Adjust the IP camera antennas.
4. Make sure the WiFi signal is strong.
5. Avoid interference by changing the frequency band of your router.
6. Check the router’s firewall.

Why wont my surveillance camera connect to WiFi?

The wireless IP camera may be too far away from the router or the access point. You set the wrong IP address on the wireless IP camera. Your router may be old and doesn’t support the camera’s WiFi channel. The firmware on the camera is old (you need to update it).

How do I get my security camera back online?

You can reset your home router and/or modem. A) Power off the camera (unplug the camera, or hold the button down for 5 seconds until the lights turn off; press it to turn it back on after about 1 minute.) 3. If the camera is still offline, you can factory reset your camera.

Can you reset a security camera?

Keep the device powered on for at least 30 seconds to complete its normal startup. Find something like a pin to press the Reset button on the camera and hold it for 15 seconds to restore the settings to factory defaults.

Can not find network host IP camera?

The No Network Host error message is an indication that the IP address of the cameras you have added to your NVR have changed. Usually, this error message can occur with cameras connected over a Power over Ethernet (PoE) switch. Fix this error message by configuring the IP address of your camera to a static IP.

How do I change from 5ghz to 2.4 GHz?

To connect your Android device to a 2.4 GHz network:

1. Unlock your device and tap the Settings app.
2. Tap Network & Internet > Wi-Fi.
3. Enable WiFi by tapping Use WiFi at the top.
4. Select a 2.4 GHz WiFi network.
5. If prompted, enter the password for the network.

Why can’t I view my security cameras online?

What to Do If You Cannot Remotely View Security Cameras Using the Internet via Port Forwarding. Make sure your cameras are connected to the network. Ensure all the ports of the network configuration are mapped to the Internet. Open the firewall in the router to allow Internet access to the camera.

Where is the reset button on a CamHi camera?

Answer: The reset button is on 1 of the 3 cables of the camera. Please press the reset button for about 10 seconds to reset it. You also can reset it on smart phone with CamHi app.

How do I change the IP address of my IP camera?

How do I change the LAN IP address of my camera?

1. Step 1: Open a web browser and enter the IP address of the camera in the address bar (default is 192.168.
2. Step 2: The default username is admin and the password field should be left blank.
3. Step 3: Click on Setup on the top menu bar.

What is the default IP of Dahua IP camera?

192.168.1.108
The default IP address is 192.168. 1.108, but you may have to change this address if it conflicts with another device on the network.

Can I use both 2.4 and 5 GHz at the same time?

Simultaneous dual-band routers are capable of receiving and transmitting on both 2.4 GHz and 5 GHz frequencies at the same time. This provides two independent and dedicated networks which allows more flexibility and bandwidth.

How do you check if my WiFi is 2.4 or 5?

1. From Notification Panel press and hold the WiFi icon until you enter WiFi settings screen.
2. Select the network properties (tap the gear icon or menu icon).
3. Depending on the Android version check: Read the “Frequency” setting – shows as 2.4 or 5GHz.

Why can’t I see my security cameras on my phone?

If you are unable to view your CCTV on your mobile device, the problem will be related to your Internet Router (WiFi) not sending an internet connection to your CCTV Recorder (DVR / NVR).