How far should toilet flange be from tile?
When you’re tiling around an already-installed toilet, plan out your pattern so that at there is at least 2 in (5.1 cm) of space between the base of the toilet and the edges of any of the tiles you’ll be laying around it.
What size toilet flange do I need for a 3-inch pipe?
The 3-Inch Flanges Many flanges are simply 3 inches in diameter, which means the top and bottom are each 3 inches wide. These flanges must install on a 3-inch-diameter schedule 40 drain pipe or directly to a 3-inch closet bend.
How far from the wall should a flange be?
12 inches
Standard drywall is 1/2 inch thick, so the plumber should set the toilet flange at least 15-1/2 inches from the center of the flange to the wall framing. The standard distance from the back wall is 12 inches, or 12-1/2 inches from the center of the flange to the wall framing.
Should the toilet flange be flush with the tile?
5 Answers. The toilet flange needs to be on top of the finished floor. Meaning the bottom edge of the flange needs to be on the same plane as the toilet. So if your toilet sits on the tile, the flange needs to be on top of the tile too.
What do you do if your toilet flange is too high?
Replacing the flange The last option when your flange is too high is to replace it. You’ll need to remove your old flange and the fitting from the pipe coming up from your bathroom floor to do this. Start by removing your toilet and breaking the outer flange portion off. You can use a hammer and a chisel.
How do I know what size toilet flange to buy?
One common standard toilet flange size is 4×3, and this is the measurement you will find beside most flanges available at your hardware or plumbing stores. The top side of the flange, which connects to the toilet, is 4 inches in diameter, while the bottom diameter of the pipe is 3 inches.
What is standard toilet flange size?
Standard Size The ring has slots for the bolts that hold the toilet down. The flange pipe can have a diameter of either 3 or 4 inches, depending on the size of the waste line, but a 4-inch hole works in both cases. Plumbers cut it with a hole saw or a reciprocating saw.
Should the toilet flange be on top of tile?
The toilet flange needs to be on top of the finished floor. Meaning the bottom edge of the flange needs to be on the same plane as the toilet. So if your toilet sits on the tile, the flange needs to be on top of the tile too. The spacing of the toilet exit “horn” and sealing surface is designed for this height.
What if toilet flange is level with floor?
5 Answers. The bottom of the flange needs to be sitting flush with (or not more than 1/8″ above) the finished floor or else the toilet will rock. Both the leaking and the rocking can warp or break the floor. A leaking flange can also rot the subfloor and lead to the accumulation of mildew and mold.
Should the toilet flange be flush with tile?
Should the toilet flange be level with floor?
Optimum flange height to aim for is 1/4 inch above the finished floor. This typically allows for almost any type of wax ring to be used and still ensure a good seal.
What is a standard size toilet flange?
The standard flange size is 3 inches in diameter. The standard plumbing hole for a toilet is the flange, the waste pipe that fits through a hole in the floor. Comprised of two parts — a pipe and a ring bolted to the floor — the flange will connect the toilet to the household’s waste line.
How do you know if you need a new toilet flange?
If you notice a lot of water pooling at the base of your toilet and inspect to find that your flange is cracked or broken, it’s time for a replacement. Make sure to properly measure your drain pipe and drain to ensure that you choose a replacement flange kit that is the right size. Loose or broken wax rings.
Does toilet flange go inside or outside pipe?
This toilet flange is designed to glue on the inside of the pipe or expand inside the pipe. Leave the old toilet flange right in place and glue on the new one at the right elevation for the floor, if it’s plastic. The flange should be sitting with the bottom edge flush with the top of the floor.
